1.Identification
1.1 GHS Product identifier
Product name | 4-(dimethylamino)azobenzene |
---|
1.2 Other means of identification
Product number | - |
---|---|
Other names | Dimethyl yellow |
1.3 Recommended use of the chemical and restrictions on use
Identified uses | For industry use only. 4-Dimethylaminoazobenzene was used as a dye for coloring polishes and other wax products, polystyrene, soap, and as a pH indicator. (4) 4-Dimethylaminoazobenzene is not currently produced or used commercially in the U.S. |
---|---|
Uses advised against | no data available |
1.4 Supplier's details
Company | MOLBASE (Shanghai) Biotechnology Co., Ltd. |
---|---|
Address | Floor 4 & 5, Building 12, No. 1001 North Qinzhou Road, Xuhui District, Shanghai, China |
Telephone | +86(21)64956998 |
Fax | +86(21)54365166 |
1.5 Emergency phone number
Emergency phone number | +86-400-6021-666 |
---|---|
Service hours | Monday to Friday, 9am-5pm (Standard time zone: UTC/GMT +8 hours). |
2.Hazard identification
2.1 Classification of the substance or mixture
Acute toxicity - Oral, Category 3
Carcinogenicity, Category 2
2.2 GHS label elements, including precautionary statements
Pictogram(s) | |
---|---|
Signal word | Danger |
Hazard statement(s) | H301 Toxic if swallowed H351 Suspected of causing cancer |
Precautionary statement(s) | |
Prevention | P264 Wash ... thoroughly after handling. P270 Do not eat, drink or smoke when using this product. P201 Obtain special instructions before use. P202 Do not handle until all safety precautions have been read and understood. P280 Wear protective gloves/protective clothing/eye protection/face protection. |
Response | P301+P310 IF SWALLOWED: Immediately call a POISON CENTER/doctor/… P321 Specific treatment (see ... on this label). P330 Rinse mouth. P308+P313 IF exposed or concerned: Get medical advice/ attention. |
Storage | P405 Store locked up. |
Disposal | P501 Dispose of contents/container to ... |
2.3 Other hazards which do not result in classification
none
3.Composition/information on ingredients
3.1 Substances
Chemical name | Common names and synonyms | CAS number | EC number | Concentration |
---|---|---|---|---|
4-(dimethylamino)azobenzene | 4-(dimethylamino)azobenzene | 60-11-7 | none | 100% |
4.First-aid measures
4.1 Description of necessary first-aid measures
General advice
Consult a physician. Show this safety data sheet to the doctor in attendance.
If inhaled
Fresh air, rest.
In case of skin contact
Remove contaminated clothes. Rinse and then wash skin with water and soap.
In case of eye contact
First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.
If swallowed
Give one or two glasses of water to drink.
4.2 Most important symptoms/effects, acute and delayed
Exposure Routes: inhalation, skin absorption, ingestion, skin and/or eye contact Symptoms: Enlarged liver; liver, kidney disturbance; contact dermatitis; cough, wheezing, dyspnea (breathing difficulty); bloody sputum; bronchial secretions; frequent urination, hematuria (blood in the urine), dysuria; [potential occupational carcinogen] Target Organs: Skin, respiratory system, liver, kidneys, bladder (NIOSH, 2016)
4.3 Indication of immediate medical attention and special treatment needed, if necessary
Absorption, Distribution and Excretion
MORE THAN HALF OF BOUND DYE IN ALL LIVER-CELL FRACTIONS IS ASSOC WITH SOL PROTEINS; OF THIS, 80% IS BOUND TO FRACTION WHICH ACCOUNTS FOR ONLY 15% OF SOL PROTEINS.
5.Fire-fighting measures
5.1 Extinguishing media
Suitable extinguishing media
Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher.
5.2 Specific hazards arising from the chemical
Flash point data for this chemical are not available. It is probably combustible.
5.3 Special protective actions for fire-fighters
Wear self-contained breathing apparatus for firefighting if necessary.
6.Accidental release measures
6.1 Personal precautions, protective equipment and emergency procedures
Use personal protective equipment. Avoid dust formation. Avoid breathing vapours, mist or gas. Ensure adequate ventilation. Evacuate personnel to safe areas. Avoid breathing dust. For personal protection see section 8.
6.2 Environmental precautions
Personal protection: particulate filter respirator adapted to the airborne concentration of the substance. Sweep spilled substance into covered containers. If appropriate, moisten first to prevent dusting.
6.3 Methods and materials for containment and cleaning up
PRECAUTIONS FOR "CARCINOGENS": A high-efficiency particulate arrestor (HEPA) or charcoal filters can be used to minimize amt of carcinogen in exhausted air ventilated safety cabinets, lab hoods, glove boxes or animal rooms ... . Filter housing that is designed so that used filters can be transferred into plastic bags without contaminating maintenance staff is avail commercially. Filters should be placed in plastic bags immediately after removal ... . The plastic bag should be sealed immediately ... . The sealed bag should be labelled properly ... . Waste liquids ... should be placed or collected in proper containers for disposal. The lid should be secured & the bottles properly labelled. Once filled, bottles should be placed in plastic bags, so that outer surface ... is not contaminated ... . The plastic bag should also be sealed & labelled. ... Broken glassware ... should be decontaminated by solvent extraction, by chemical destruction, or in specially designed incinerators. /Chemical Carcinogens/
7.Handling and storage
7.1 Precautions for safe handling
Avoid contact with skin and eyes. Avoid formation of dust and aerosols. Avoid exposure - obtain special instructions before use.Provide appropriate exhaust ventilation at places where dust is formed. For precautions see section 2.2.
7.2 Conditions for safe storage, including any incompatibilities
PRECAUTIONS FOR "CARCINOGENS": Storage site should be as close as practical to lab in which carcinogens are to be used, so that only small quantities required for ... expt need to be carried. Carcinogens should be kept in only one section of cupboard, an explosion-proof refrigerator or freezer (depending on chemicophysical properties ...) that bears appropriate label. An inventory ... should be kept, showing quantity of carcinogen & date it was acquired ... . Facilities for dispensing ... should be contiguous to storage area. /Chemical Carcinogens/
8.Exposure controls/personal protection
8.1 Control parameters
Occupational Exposure limit values
NIOSH usually recommends that occupational exposures to carcinogens be limited to the lowest feasible concn.
NIOSH considers 4-dimethylaminoazobenzene to be a potential occupational carcinogen.
Biological limit values
no data available
8.2 Appropriate engineering controls
Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the end of workday.
8.3 Individual protection measures, such as personal protective equipment (PPE)
Eye/face protection
Safety glasses with side-shields conforming to EN166. Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Skin protection
Wear impervious clothing. The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace. Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique(without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands. The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the standard EN 374 derived from it.
Respiratory protection
Wear dust mask when handling large quantities.
Thermal hazards
no data available
9.Physical and chemical properties
Physical state | Orange powder |
---|---|
Colour | YELLOW CRYSTALLINE LEAFLETS |
Odour | no data available |
Melting point/ freezing point | 295°C(dec.)(lit.) |
Boiling point or initial boiling point and boiling range | 193°C(lit.) |
Flammability | Not combustible. |
Lower and upper explosion limit / flammability limit | no data available |
Flash point | 170°C(lit.) |
Auto-ignition temperature | no data available |
Decomposition temperature | no data available |
pH | no data available |
Kinematic viscosity | no data available |
Solubility | In water:13.6 mg/L |
Partition coefficient n-octanol/water (log value) | log Kow= 4.58 |
Vapour pressure | 3e-07 mm Hg (est.) (NIOSH, 2016) |
Density and/or relative density | 1.027g/cm3 |
Relative vapour density | 7.78 (Relative to Air) |
Particle characteristics | no data available |
10.Stability and reactivity
10.1 Reactivity
no data available
10.2 Chemical stability
Stable under recommended storage conditions.
10.3 Possibility of hazardous reactions
4-DIMETHYLAMINOAZOBENZENE can detonate, particularly if sensitized by the presence of metal salts or strong acids. May form toxic gases with acids, aldehydes, amides, carbamates, cyanides, inorganic fluorides, halogenated organics, isocyanates, ketones, metals, nitrides, peroxides, phenols, epoxides, acyl halides, and strong oxidizing or reducing agents. May form flammable gases with alkali metals. May react explosively with strong oxidizing agents, metal salts, peroxides, and sulfides. May react explosively with strong oxidizing agents, metal salts, peroxides, and sulfides.
10.4 Conditions to avoid
no data available
10.5 Incompatible materials
STABILITY: This chemical is sensitive to heat and light. Solutions of this chemical in water, DMSO, 95% ethanol or acetone should be stable for 24 hours under normal lab conditions.REACTIVITY: This chemical is incompatible with strong oxidizing agents and strong acids.
10.6 Hazardous decomposition products
no data available
11.Toxicological information
Acute toxicity
- Oral: no data available
- Inhalation: no data available
- Dermal: no data available
Skin corrosion/irritation
no data available
Serious eye damage/irritation
no data available
Respiratory or skin sensitization
no data available
Germ cell mutagenicity
no data available
Carcinogenicity
The Human Health Assessment Group in EPA's Office of Health and Environmental Assessment has evaluated dimethylaminoazobenzene for carcinogenicity. According to their analysis, the weight-of-evidence for dimethylaminoazobenzene is group B2, which is based on no evidence in humans and sufficient evidence in animals. As a group B2 chemical, dimethylaminoazobenzene is considered to be probably carcinogenic to humans.
Reproductive toxicity
No information is available on the reproductive or developmental effects of 4-dimethylaminoazobenzene in humans. Animal studies have reported birth defects in the offspring of mice exposed to 4-dimethylaminoazobenzene.
STOT-single exposure
no data available
STOT-repeated exposure
no data available
Aspiration hazard
no data available
12.Ecological information
12.1 Toxicity
- Toxicity to fish: no data available
- Toxicity to daphnia and other aquatic invertebrates: no data available
- Toxicity to algae: no data available
- Toxicity to microorganisms: no data available
12.2 Persistence and degradability
Recovery of 0.29 ppm N,N-dimethyl-p-(phenylazo)aniline incubated with an original culture of settled domestic wastewater after 7 days was at trace levels and it was not detected following 1st, 2nd, and 3rd subcultures after 7 days each(1).
12.3 Bioaccumulative potential
Using a reported log octanol/water partition coefficient of 4.58(1), an estimated BCF of 1780 was calculated(2,SRC). Based on this estimated BCF, N,N-dimethyl-p-(phenylazo)aniline should bioconcentrate in aquatic organisms(SRC).
12.4 Mobility in soil
Using a reported log octanol/water partition coefficient of 4.58(1), an estimated Koc of 7390 was calculated(2,SRC). Based on this estimated Koc, N,N-dimethyl-p-(phenylazo)aniline should adsorb to soils and sediment. Since N,N-dimethyl-p-(phenylazo)aniline has a pKa of 3.226 at 25°C(3), and it exists partially as a cation, the extent of its adsorption to soils and sediments may be affected by the pH of the medium.
12.5 Other adverse effects
no data available
13.Disposal considerations
13.1 Disposal methods
Product
The material can be disposed of by removal to a licensed chemical destruction plant or by controlled incineration with flue gas scrubbing. Do not contaminate water, foodstuffs, feed or seed by storage or disposal. Do not discharge to sewer systems.
Contaminated packaging
Containers can be triply rinsed (or equivalent) and offered for recycling or reconditioning. Alternatively, the packaging can be punctured to make it unusable for other purposes and then be disposed of in a sanitary landfill. Controlled incineration with flue gas scrubbing is possible for combustible packaging materials.
14.Transport information
14.1 UN Number
ADR/RID: UN2811 | IMDG: UN2811 | IATA: UN2811 |
14.2 UN Proper Shipping Name
ADR/RID: TOXIC SOLID, ORGANIC, N.O.S. |
IMDG: TOXIC SOLID, ORGANIC, N.O.S. |
IATA: TOXIC SOLID, ORGANIC, N.O.S. |
14.3 Transport hazard class(es)
ADR/RID: 6.1 | IMDG: 6.1 | IATA: 6.1 |
14.4 Packing group, if applicable
ADR/RID: III | IMDG: III | IATA: III |
14.5 Environmental hazards
ADR/RID: no | IMDG: no | IATA: no |
14.6 Special precautions for user
no data available
14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
no data available
15.Regulatory information
15.1 Safety, health and environmental regulations specific for the product in question
Chemical name | Common names and synonyms | CAS number | EC number |
---|---|---|---|
4-(dimethylamino)azobenzene | 4-(dimethylamino)azobenzene | 60-11-7 | none |
European Inventory of Existing Commercial Chemical Substances (EINECS) | Listed. | ||
EC Inventory | Listed. | ||
United States Toxic Substances Control Act (TSCA) Inventory | Listed. | ||
China Catalog of Hazardous chemicals 2015 | Not Listed. | ||
New Zealand Inventory of Chemicals (NZIoC) | Listed. | ||
Philippines Inventory of Chemicals and Chemical Substances (PICCS) | Listed. | ||
Vietnam National Chemical Inventory | Listed. | ||
Chinese Chemical Inventory of Existing Chemical Substances (China IECSC) | Listed. |
16.Other information
Information on revision
Creation Date | Aug 12, 2017 |
---|---|
Revision Date | Aug 12, 2017 |
Abbreviations and acronyms
- CAS: Chemical Abstracts Service
- ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
- RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
- IMDG: International Maritime Dangerous Goods
- IATA: International Air Transportation Association
- TWA: Time Weighted Average
- STEL: Short term exposure limit
- LC50: Lethal Concentration 50%
- LD50: Lethal Dose 50%
- EC50: Effective Concentration 50%
References
- IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home
- HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm
- IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/
- eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en
- CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple
- ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp
- ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg
- Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp
- ECHA - European Chemicals Agency, website: https://echa.europa.eu/